无遮挡吃胸膜奶免费看视频,欧美三级全黄牲交视频,无码精品日韩专区第一页,八戒八戒看片在线观看网盘

渣漿泵的比轉速類型和規格

離心泵的類型和規格很多，結構也多種多樣，很難對其性能進行綜合比較，而且在研制新型泵時，由于泵內流動狀況復雜，往往在參照現有泵的基礎上進行試驗和設計。這樣，在有的分類、試驗設計和產品系列化方面，就引進了比轉速這一概念,用n.表示。
1.比轉速表達式
取相似定律的式(1 - 55)及式(1 -56).消去2u.得:
取20C時清水密度ρ= 1000kg/m3，g=9. 81m/s2，有:
式中n----離心泵轉速，r/min；
    Q----流量(最高效率下，對于雙吸葉輪，取值為葉輪總流量的一半),m/s;

H----揚程(最高效率下 ,對于多級泵應以H/i代入,i為級數),m。
式(1-61)是我國習慣采用的比轉速表達式，它是有因次的。在歐美國家習慣用，采用的單位不同,計算值也不同,本質上沒有區別。比轉速的因次是(m/s)”，它正好是重力加速度因次的3/4次方，因此把比轉進除以”，再把轉速，汝為角速度，就變為無國次，稱為型式數。GB/T 3216 205規定的量式數計算公式為:
比轉速和型式數之間的關系為:

比轉速是由相似定律導出的綜合參數，它是工況的函數，對于同一臺泵來說，不同渣漿泵工況就有不同的比轉速，應以其設計工況點(或最高效率點)的比轉速來代表這臺泵的比轉速。幾何相似的泵在各自最高效率點處的工況相似,因此其比轉速相等。比轉速不同的泵，其幾何形狀一定不相似:比轉速 相同的泵其幾何形狀也不一定完全相似。

Specific speed type and specification of slurry pump

There are many types, specifications and structures of centrifugal pumps, so it is difficult to make a comprehensive comparison of their performance. Moreover, in the development of new pumps, due to the complex flow conditions in the pump, tests and designs are often carried out on the basis of referring to the existing pumps. In this way, the concept of specific speed is introduced in some classification, experimental design and product serialization, which is expressed by n.

1. Expression of specific speed

Take the formula (1-55) and formula (1-56) of the similar law, and eliminate 2U

At 20c, the clear water density ρ = 1000kg / m3, g = 9.81m/s2, including:

Where, N - rotating speed of centrifugal pump, R / min;

Q --- flow (under the highest efficiency, for double suction impeller, the value is half of the total flow of impeller), M / S;

H ---- head (under the highest efficiency, H / I shall be substituted for multistage pump, I is the series), M.

Formula (1-61) is the expression of specific speed which is used in our country. It has dimensions. In European and American countries, it is used in different units, and the calculated value is different, so there is no difference in essence. The factor of specific speed is (M / s) ", which is exactly the third fourth power of the factor of gravity acceleration. Therefore, divide the specific speed by", and then turn the speed, Ru, into angular speed, which becomes stateless, called the type number. According to GB / T 3216 205, the calculation formula of the quantity formula is:

The relationship between specific speed and type number is as follows:

Specific speed is a comprehensive parameter derived from the law of similarity, which is a function of working conditions. For the same pump, different slurry pump working conditions have different specific speed. The specific speed of the design working point (or the highest efficiency point) should be used to represent the specific speed of the pump. Pumps with similar geometry have similar working conditions at their highest efficiency points, so their specific speed is equal. The geometry of pumps with different specific speed must be different: the geometry of pumps with the same specific speed may not be exactly similar.